Urine Stain Remover with Hydrocide CS18GL 1647-1702

$46.95

URINE STAIN REMOVER By BridgePoint

1 Gallon

Blend of surfactants, solvents and hydrogen peroxide attack stains in multiple ways
Anti-resoiling polymers allow Urine Stain Remover to be applied without extraction and fear of resoiling
For minor stains, an application of Urine Stain Remover is all that is needed

Also Available by the Case (Add QTY 4 to cart)

8 in stock

URINE STAIN REMOVER

Urine Stain Remover is the go-to solution for removing difficult urine stains from carpet. It uses surfactants to penetrate deeply into the fibers, delivering a potent shot of peroxide that removes stains caused by urine, vomit, blood and other organic stains. It also contains the odor encapsulating and bonding power of Bridgepoint Systems Hydrocide. As it neutralizes and eliminates the yellow stain, it also neutralizes the odor.

Available Sizes ▪ 1 gal. / 3.8 L bottles

Item # BP-CS18GL
MFR # 1647-1702
MFR Legacy # CS18GL
AKA # 8.619-134.0, B07BTLMYWV, BPCS18GL, INT1870GAL,

Specifications

Form: Liquid
pH: 5.4
Dilution Ratio: RTU
Certification: Green Balance

Features

If Urine Stain Remover can’t get it out, it’s not getting out.
Blend of surfactants, solvents and hydrogen peroxide attack stains in multiple ways
Anti-resoiling polymers allow Urine Stain Remover to be applied without extraction and fear of resoiling
For minor stains, an application of Urine Stain Remover is all that is needed

Many times normal pet odor decontamination procedures remove the yellow staining that accompanies many pet urine deposits. But when it doesn’t, reach for Urine Stain Remover with Hydrocide. Simply spray the stain full strength and allow it to work for 3 to 8 hours and the stain will disappear. This is a product that will deliver truly amazing results and there’s no need to neutralize or rinse. Goes on at an acidic pH of 5.4 but self-neutralizes to a neutral pH of 7 as it dries.

Pet Deodorizers

Manufacturer Info

Directions

Thoroughly clean and clear water rinse stained area using a Water Claw to flush out organic source material.
Apply Bridgepoint’s USR with Hydrocide full strength directly to urine stain. Be aware that its use will limit the capability of any remaining bacteria/enzyme products.
Allow three to eight hours for stain to disappear (depending on temperature and conditions)
Repeat treatment as necessary to remove the stain. For any remaining odors, use Bio-Modifier or Bio-Charge.

Urine Removal System Directions

For light to medium urine damage:

Apply our all-in-one Pet Zone urine stain and odor removal solution, allow to dwell for 10 minutes. Extract. If stain is still
present, apply more Pet Zone or Urine Stain Remover and allow to dwell until dry.

For medium to heavy urine damage:

STEP 1: Decontamination with Urine Neutralizer

- - Dilute Urine Neutralizer with 4 parts water in a pump or electric sprayer. Apply to the full area of contamination. Remember that the area of contamination under the carpet may be more than twice the size of the stain on the surface. Apply enough to reach the pad and subfloor. (Caution: some subfloors may be susceptible to water damage, be careful to not over apply.) Allow to dwell 10 minutes.
  - Extract Urine Neutralizer with a Water Claw® or Flash Extractor™ tool. Flush clear hot water around the Water Claw® tool several times to remove dissolved urine contamination. For faster decontamination, use a Water Claw® extractor with Injectors.

STEP 2: Odor neutralization with Bio-Modifier Xtreme

- - Dilute with 1 part warm water. Apply Bio-Modifier Xtreme heavily enough to penetrate all affected areas. Compressing the pad by stepping on it, or pushing down with a Water Claw, will disperse the product and provide even coverage. Use of a subsurface injection system such as the Injectimate or syringe can also be used to reach the contamination.
  - Hydrocide Xtreme can be added to solution if additional odor neutralizing is needed.

STEP 3: Stain removal with USR

- - Polyester, olefin, triexta and solution-dyed nylon fibers will not stain.
  - Apply Urine Stain Remover to the surface fibers and allow to dwell for 10-20 minutes. Urine Stain Remover is ready to use and requires no dilution. Extract. If stain is still present, apply more Urine Stain Remover and leave.
  - Note: don’t saturate pad with Urine Stain Remover since the stain is on the fibers.